• Parking Lot Safety

Shopping Cart Corral Bump

Product Description

Our RubberForm Shopping Cart Corral Bump keeps shopping carts where they belong till your customers need them: in the cart corral. It’s made with 100% American recycled extruded composite material that won’t crack, crumble, or corrode no matter the heat, cold, rain, ice, or snow.

The traditional metal bar or concrete or asphalt bump options are harder to see and easier to trip over. Our corral bump tells your customers you care about their safety without making it difficult to get carts in and out, and keeps them from rolling into you or your vehicle.

$145.76
Add to quote

Specifications:

  • 8” W x 1.25” H x 8’ L standard length
  • Custom lengths are available 30 lbs 1.5” wide
  • Thermoplastic yellow reflective strip
  • Custom lengths available Made in the USA with 100% American TPV Composite material.

Download Spec Sheet

Download

Product Description

When we designed our Shopping Cart Corral Bump, we didn’t just make a smaller speed bump, we custom designed one from the ground up. We asked some of our colleagues at North America’s largest retailers and their vendors who make cart corrals. Have you ever seen some poor shopper repeatedly push the same cart into a corral, only to have it roll right back out? We carefully innovated our corral bump to solve this by keeping carts in, but still easy to pull back out when you want due to tapered ramps on both sides. Our safety yellow strips and reflective glass beads maintain maximum visibility. The result? Minimize your liability and keep your customers safe while they shop. 

Our corral bumps are made with 100% American recycled thermoplastic composite material. And since parking lots are subject to every temperature extreme in our northern hemisphere, our corral bumps are made to withstand them. Neither the searing heat of the summer sun or the frigid cold of North American winters will affect them. No chipping, no warping, no spalling. They’re simple to install and just as easy to remove and relocate if needed.

Models

RF-SCCB8.1.25

  • 30 lbs
  • 1-1/4”H x 8”W x 8’L

Key Features

  • Enhances safety and minimizes liability from pedestrian, vehicle, and shopping cart incidents in parking lots
  • Tapered ramps on both sides allow carts to be easily rolled into/out of cart corrals
  • Easy and straightforward to install
  • All-weather durability – will not chip, crack, spall, or need repainting
  • Made in the USA with 100% American thermoplastic composite TPV material

Hardware Kits

RF-RSS3.8-4

  • 3/8” x 4”L Rugged Structural Screw

RF-CLM-1.10.1BK

  • ChemLink M1 structural adhesive

FROM ONE SPECIALIST TO ANOTHER

Related products

Whether you need speed bumps, roofing support, curb ramps, or more, RubberForm specializes in safety and risk mitigation.

Cart Corral, 8' Length, yellow stripe, Priced Per 8ft Unit
Cart Corral, 8' Length, yellow stripe, Priced Per 8ft Unit
Shopping Cart Corral Bump: 8in wide, 8ft long x 1.25in tall, with yellow stripe
Learn More

FREQUENTLY ASKED

What style speed bumps and speed humps do you manufacture?

RubberForm has the largest and most diverse traffic calming product line in the USA. We offer our MLSB and RK Speed Bump and Speed Hump Product Lines. nOur MLSB2.5 speed bump is a 2-½” high by 36” long with 2 ATTSA yellow reflectors, which will slow traffic to 5 to 10 mph. nOur MLSB3 speed bump is a 3” high by 36” long with bright yellow reflector strip, which will slow traffic to 5 mph. nOur MLSB4 is the most aggressive speed bump on the market. This 4” high speed bump will slow traffic to about 3-5 mph and was designed for use on construction sites and trucks (not recommended for pedestrian or personal vehicle use).nWe offer 3 products in our RK speed bump and speed hump product line. All sections are 24” long so they can be sectioned together for any road/lane width needed.nThe RK-10 speed bump is a 1-7/8” high x 10” wide x 24” long section with end cap sections. nOur RK-18 mini speed hump is a 1-7/8” high x 18” wide x 24” long section with end cap sections.nOur RK-36 speed hump is a 1-7/8” high x 36” wide x 24” long section with end cap sections.n

How are your speed bumps and speed humps anchored down?

We offer a lag bolt mounting system consisting of a lag bolt, anchor, and washer to anchor into pavement or concrete. There are 4 anchor holes for our MLSB product line in each speed bump. For temporary situations, you can just lay them down or moor them in place with our GRK’s RSS™ Rugged Structural Screw. For our RK Series speed bump and speed humps, there are 2 anchor holes for each 24” long section.

Can your speed bumps and humps be installed on a gravel road?

Yes, our MLSB traffic calming product line, with a 24” rebar spike or gravel earth screw can be purchased from RubberForm. These rebar spikes and earth screws should be checked periodically to make sure they have not crept up to create a hazard.

What is the reflective material on your speed bumps and speed humps?

For our MLSB2.5 we use 2 embedded AASHTO approved yellow reflectors. On our MLSB3 and MLSB4, we use a high visibility reflective yellow tape. For our RK series speed bumps and speed humps we use a special-formulated safety yellow paint with reflective glass beads.

Are these speed bumps removable, i.e., can they be moved to a new location or taken up for snowplows during the winter season?

Yes, if you need to remove them for the winter, just unbolt or unscrew the bolts/screws and store for the season. Seal the holes with Eco-Bond so water, dirt and rocks do not get lodged in the holes.

How long are your speed bump/speed hump sections?

Our line of MLSB speed bumps come in 36” long pieces that connect with a dovetail, allowing you to create the length you need. Our RK series speed bump and speed humps come in 24” sections that link together with a special dual-flange connector which also allows you to create any length you need.

What is the rubber material your speed bumps and speed humps are made of?

We have custom-formulated the right material for hard traffic over many years of use. We use masticated recycled rubber, which is harder and more durable than virgin clay-filled rubber or crumb rubber and poly compounds.

What is the turnaround time for your speed bumps and speed humps?

Our speed bumps and speed humps are in stock and can usually be shipped out the following day. Larger orders (greater than 100 units) may take a little longer - please provide us enough time to manufacture and let us know when you will need delivery.

Are your speed bumps and humps truly made in the USA?

RubberForm is one of the only true U.S. manufacturers of rubber speed bumps and speed humps. They are made from domestically sourced scrap tire rubber, manufactured, and assembled in the U.S. We believe that this is the only way to maintain our high standard of quality control.